My first thought after reading this title: Oh cool, they've taken part in a drill and used the motor. I don't really know what that looks like inside a power drill. This will be an interesting post.
Immediately opened it and laughed out loud. Perfect execution, no notes.
shermantanktop 20 minutes ago [-]
Not enough gaffer/duct tape! But the inability to bank to the right side is perfect. Just do a 270 to the left.
Aurornis 34 minutes ago [-]
Same thought here. Did not expect this level of jank but I loved every photo and word.
The contrast between the 3D scanning and bolting a power drill to the side was fun.
bombcar 2 hours ago [-]
This is exactly what I wanted even though it was not at all what I expected.
madaxe_again 2 hours ago [-]
You’d love how I’m starting my generator. Same drill. Hodgepodge of springs and string to manage the choke. ESP32 committing obscenities in the middle of all of it.
Gee101 2 minutes ago [-]
This absolutely deserves to be documented
Doohickey-d 1 hours ago [-]
I do wonder how long the electronics, motor and little (plastic) gears in the drill would last with this. Especially since I'd suspect that it's designed for intermittent use, where it has time to cool down between each screw / hole drilling that you'd do normally. If you drive 2 miles in one go, that'll be a lot of heat that doesn't have time go anywhere.
Somehow I'd suspect that it won't last all that long...
lisp2240 9 minutes ago [-]
Drills are used sporadically. If a drill was used intermittently it would be on most of the time and occasionally off.
Wonder how this would work with an impact? Also, since it already uses one-way bearings, could another drill/impact be fitted to the other side so that there are two “gears” available?
echelon_musk 2 hours ago [-]
A good friend of mine told me he would frequently come across a guy who had modified his bicycle with an electric drill.
He would see him leaning over and pulling the trigger get an electric assist on the uphill section of the commute.
delichon 3 hours ago [-]
What is that 3D printed wheel made of that it can support over half of your weight while bumping along a road?
Yes, but you could have made it out of PETG just the same. I have some PETG parts here that we have tried to break but couldn't, that stuff is ridiculously strong for its weight if you use the right infill and you take the layer direction into account when designing the part.
_joel 3 hours ago [-]
Direct drive, yes, also direct drill.
Watch out for the gear change, may end up in hammer action.
bzmrgonz 18 hours ago [-]
You know you could have used a 90 degree chuck buddy. Or better yet, an angle grinder to make it a friction drive from above.
jacquesm 1 hours ago [-]
It's got 2 miles of range, adding those complications would likely eat up a lot of the range.
nchmy 59 minutes ago [-]
video or it didnt happen!
gniv 3 hours ago [-]
Turning right seems hard.
erelong 1 hours ago [-]
add another wheel on the other side of the drill for a kind of sidecar-like stability? (tricycle style?)
tamimio 2 hours ago [-]
Missed the opportunity to add vacuums and blowers and go upside down plus lateral and rotational movement, with fancy dark themed site and buzz words all over :)
blackspacx 4 days ago [-]
[flagged]
Rendered at 20:40:16 GMT+0000 (Coordinated Universal Time) with Vercel.
Immediately opened it and laughed out loud. Perfect execution, no notes.
The contrast between the 3D scanning and bolting a power drill to the side was fun.
Somehow I'd suspect that it won't last all that long...
https://www.youtube.com/@RedGreenTV
He would see him leaning over and pulling the trigger get an electric assist on the uphill section of the commute.
https://en.wikipedia.org/wiki/Acrylonitrile_styrene_acrylate
Watch out for the gear change, may end up in hammer action.